In our last installment of the Rooibos Sewalong, we learned all about curved seams and finishing. Now it’s time to install the all-in-one facing. We’ll also talk about adding the piping, and I’ll show you some clever tricks for getting it just so.
1. Stitch the facing pieces together at the shoulders, and press the seams open.
2. Now you want to mark the seam of the neckline on your bodice, which is 5/8″ from the edge. Remember, you’ve already stitched the front and back bodice together at the shoulders in our last installment.
You can mark the seamline in any number of ways. Chalk and a ruler is find. But I prefer to simply stitch a line of basting all the way around the neckline. It’s a super fast way to mark a seam allowance, since your sewing machine basically does the measuring for you.
I’m going to be using piping for mine. If you’re not using it, you can skip the piping steps.
3. Take your piping, and pin it all around the neckline on the right side of the bodice, aligning the stitching on the piping (right next to the cord) with the seamline you’ve just marked. Use plenty of pins to hold it in place.
4. When you reach an inner corner like this with your piping, you can simply fold the piping seam allowance (as shown above) to get a nice point.
5. For an outer corner, clip the piping seam allowance to get it to bend around the tip of the point.
6. Overlap the piping at the center back, as shown. Make sure the ends point toward the edge, as shown above. Pin in place securely.
7. Baste the piping to the neckline using a contrast color thread. Here, I’m going to use a black thread.
You can use a piping foot or a zipper foot to stitch the piping on, stitching right up against the corded part of the piping. I use a #12 foot for the Bernina (suggested by the fine ladies at Modern Domestic)
Here’s how it will look on the wrong side of the bodice. You can clearly see the stitches from this side, which will make it very easy to sew later.
8. With right sides together, pin the facing to the bodice. You should now have the piping sandwiched between the bodice and the facing. Pin with the bodice facing up, towards you. This is because you’ll be stitching from the bodice side (not the facing side), so you want to be able to remove the pins easily.
Here’s how it looks from the facing side.
9. Using matching thread, stitch the bodice to the facing. Stitch directly over your contrasting basting stitches.
10. Remove all of the basting.
11. Clip the corners of the collar points, and clip into the inner corners to make this easier to turn. I actually ended up clipping away a bit more from the collar points than this.
12. Clip around the inner curves of the neckline, all the way around. Clipping the inner curves will help your turn the seam out.
13. Grade the seam. To do this, I trimmed the neckline seam a little. Then I trimmed the seam allowance of the bodice (but not the facing) by about half. Trimming the seam allowance to different widths like this keeps it from being too bulky.
14. Now we’re going to understitch the seam allowance. To do this, first press the neckline seam allowance toward the facing. As the pattern states, you won’t be able to understitch the collar area of the neckline. So just try to understitch up to that area.
15. Understitch the facing. To do this, stitch the seam allowance to the facing, close to the stitching line.
16. Turn the bodice and facing right side out and press. You might want to use a bamboo point turner to get crisp points on those collars!
If it doesn’t seem to be turning correctly, take a look at the clipping you did in step 11. Make sure you clipped deeply enough into the inner corners (but take care not to cut through the stitching!)
17. You might want to finish the lower edges of the facing pieces now. Try a finish that isn’t too bulky, such as pinking, serging, or zigzagging.
Now we’re ready for the all-in-one facing trickery!
18. First, lay your bodice out flat, as shown. The bodice and facing should be neatly aligned, with the facing on top.
19. Roll the bodice facing from one armhole edge, towards the other armhole edge.
20. Now we’re going to flip the facing underneath. To start, flip the facing out as shown.
21. Next, flip the facing under and align the armhole edges of the bodice and facing. The right sides should be together.
22. Stitch the bodice to the facing along the armhole.
23. Pull the garment through the shoulder area in order to pull it right side out.
24. Stitch the second armhole in the same manner (steps 18-23).
25. With right sides together, stitch the right side seam of the bodice. Stitch in one continuous seam, stitching the front of the bodice to the back of the bodice, and the front facing to the back facing.
That’s it! Next up, we’re going to be discussing sewing the pockets on Friday!
Some related posts you may be interested in: