172

Tutorial: Installing an Invisible Zipper (with video)

How to Sew an Invisible Zipper from Colette Patterns on Vimeo.

finished zipper

Zippers can be daunting even for experienced sewers. The reason? Zippers are often installed the wrong way.

Lots of seam ripping and swearing ensues, especially when it’s a simple mistake. There’s no need to be scared of zippers anymore!

We’re here to help. With a little bit of practice you’ll get it. Remember that it takes time to master something new and even then, it’s easy to make mistakes. Give yourself a break if you feel overwhelmed and come back to it later.

Invisible zippers are one of the nicest looking zippers because they are (as the name implies) invisible. We love to use this zipper in the garments we make for ourselves and recommend them often in our patterns. They look clean and professional, and (even better), they are perhaps the easiest to install!

items needed

Items Needed:

  • invisible zipper
  • thread
  • scissors
  • pins
  • invisible zipper foot
  • zipper foot
  • garment

IMG_8170

Before we start, take a look at the back of your invisible zipper. Do you notice how the coils of the zipper curl toward the back? This is what makes the zipper less visible than a normal zipper. But for sewing it in, it’s helpful to uncurl those coils and press the zipper flat first. This lets you stitch a bit closer to the coils.

IMG_8171

1) Lay your zipper wrong side up, with the zipper open. Set your iron on warm (or the synthetic setting). Use your fingers to uncurl the teeth of the zipper while pressing it flat with the tip of your iron. Do this on both sides.

measure zipper

zipper tape is usually smaller than 5/8″

2) Put your garment right side up, facing you. Place the zipper face down on the fabric. Here we left about 1/4″ between the zipper tape and the edge of the fabric because the zipper tape was thin. Use a seam guide or measuring tape to make sure the zipper coil lines up with the seam allowance. In this instance a 5/8″ seam allowance was used.

pin first side

place the pins parallel to the zipper

3) Pin the zipper to the garment. Notice that the zipper is face down in this photo as it should be every time you sew an invisible zipper.

line up zipper in foot

4) Having inserted the invisible zipper foot into your machine, lower the foot down onto the zipper. Make sure that the zipper coil is in the left groove of the foot.

sewing first side

sewing slowly helps prevent the fabric from puckering

5) Stitch the pinned zipper. Sew slowly, removing the pins before they reach the foot. Stop when you reach the end of the zipper, or the mark on your garment where the zipper should end. Backstitch about 1/2 inch.

pinned second side

6) For the opposite side, pin the zipper to the garment so that it resembles the above photo. Again, make sure that the right side of the fabric is facing up. So you are pinning the zipper to the right side of the fabric.

testing zip

double check your zipper before sewing

7) Close the zipper to make sure that you’ve pinned it correctly. This part can easily get twisted, so it’s best to double check before you do any sewing. Once you’ve checked, unzip it before sewing.

sewing second side

remember to back stitch at the end of the zipper

8) Sew the zipper as you did the other side. However, this time make sure that the zipper coil is in the right side groove of the foot.

iron zipper

9) The zipper is now firmly in your garment, you did it! Just a few more steps to go. Pull the zipper closed and lightly press before continuing.

pin seam allowance

make sure the seam allowances line up

10) Sandwich the zipper in the seam allowance and pin carefully down the rest of the seam. The zipper tail should be out of the way, otherwise it’ll get caught in the stitches you’re about to make.

zipper foot sewing

keep your seam line even to avoid puckering

11) Remove the invisible zipper foot and replace with a standard zipper foot. Put the foot to the left of the zipper. Starting about 1/4″ or so above the end of the zipper, slowly stitch forward then do a small back stitch. The zipper adds bulk right here and will try to pull away from the needle. Instead of forcing the needle to be right next to the zipper, just stitch slowly as close to the zipper as you can. Sew down the remainder of your garment.

stitched seam

12) You can see that the stitching lines have about 1/8″ of space between them. It’s okay that they don’t match up! If you are able to match them up perfectly, then do so. Even with that small bit of space your zipper will still look good.

finished zipper

And there you have it! A lovely finished invisible zipper.

Enjoyed this post?

Get all of our tips, tutorials, and discussions delivered to your inbox – it’s free!


Like what you read here? Subscribe to our blog via email so you don’t skip a stitch! And sign up for our weekly Snippets email for even more sewing tips and tricks.

On , Marie Roche said:

Is it correct that an invisible zipper foot cannot be used on all fabrics? I heard a sewing instructor say this, that invisible zippers should only be used if the fabric has a bit of loft. Is this true?
Thank you for this tutorial it was clear and very helpful.

Marie Roche

On , Antoinette said:

Felt confident with the instructions and when I attempted to sew the invisible zip, I managed to do it finally. Thank you

On , Brittan said: | brittansalisbury.wordpress.com

Its true, Invisible zippers are HARD, I think step 11 can be the toughest .

I was shocked when I finally started to get zippers right right! haha.

Another great tutorial, I love the little tips pointed to by arrows. Good job! xo

On , Caroline said: | l-p.cc

This tutorial assumes its readers have an “invisible zipper foot.” So many of us are sewing on ancient machines. It’s possible to make do. Even new machines sometimes don’t have zipper feet. Husqvarna Viking owners will be using their buttonhole (C) foot. No joke. The Juki F-series doesn’t come with an invisible zipper foot so I have made do other feet (instead of special-ordering a foot), sometimes with even better results. As long as the foot isn’t sliding over the coils and one is able to sew in a straight line, finding a target line on the zipper (usually a margin with a visibly different weave closest to the coil) and sewing along it works well.

On , Sarai said: | colettepatterns.com

We should point out that most fabric stores carry very cheap (I think I’ve bought one for $3) plastic snap on invisible zipper feet. Of course, they don’t fit on all machines, but if you have one that it will work with, it’s a really cheap option.

On , Caroline said: | l-p.cc

Hmmmm. That might be an option for me for the Juki! Thanks Serai.

On , Reana Louise said: | curvespatternsandpins.blogspot.com

I’ve purchased a generic cheap plastic foot for invisible zippers and whilst it was a bit of an effort getting it on, it still worked perfectly fine once it was (finally!) on there.

Since then my boyfriend spoilt me with the proper metal foot (probably sick of my whinging! ha!) and working with it is a total breeze- but the plastic ones still work fine if it’s your only option.

On , Sarai said: | colettepatterns.com

This is basically my experience. The real metal feet are indeed nicer, but I’ve sewn zippers with cheap feet in the past and it worked fine. I don’t see much harm in experimenting with it if the more expensive feet are inaccessible.

On , Gordana Radovanovic said: | MyFimoKitchen

Hi Caroline,I’ve just discovered your blog seeing the zipper tut.Unexpectably for me,you had a great advice for the Husky mashine which I own,thanks a lot!Also,I think your tip is great,since the invisible zippers are lovely looking but a real nightmare for sewing…greetings from Serbia

On , Caroline said: | l-p.cc

Hi Gordana,

Happy that you found what you needed. Here is a more specific tutorial for the Husqvarna Viking machines which lack a dedicated zipper foot:

http://www.geocities.com/fashionavenue/3824/invszipper.html

On , Adi said:

Thanks for mentioning that Husqvarna users can use the button foot! I would never have thought of that.

On , Katrina said: | katriniella.wordpress.com

I’ve done invisibible zippers so many times, and I STILL can’t get it to look good! Thanks for the tutorial–time to practice, I think.

On , sewer said:

Caroline:

It is possible to install an invisible zipper without the special foot, but it is harder. I’ve sewn on an industrial Juki; it’s a very common, cheap, and easily available foot. I had to buy one for my home sewing machine, again, it was easy to find and was inexpensive.

The traditional method of installing an invisible zipper has been illustrated, in which the zipper is installed before the seam is sewn. I once took a class in which we installed the zipper into a closed seam, but that involved basting part of the seam first. It was truly fool-proof and avoided the bubble at the bottom of the zipper. I don’t recall all the steps, otherwise I would post the method.

On , Caroline said: | l-p.cc

Thanks – I know it’s possible and I mentioned how. I’m not sure you read my comment. The invisible zipper foot for my machine is not available at any stores in Portland. There is only one official Juki dealer and according to him it needs to be special-ordered. Which is why I was thankful for Serai’s comment. $3 is a nice price.

On , Christina Draper said:

I absolutely love this method. It truly is foolproof. Just be sure to measure and mark where the closed end of the zipper hits in the seam and backstitch over that spot. Once the zipper is on, you can then take a seam ripper to let it out, not going past your backstitched spot.

On , Cindy said:

I learned how to install an invisible zip from my mom and she always used the basted seam method, however, I’m going to try this one too just to see the difference. I don’t have an invisible zipper foot either but I’m going to look at my local fabric shop and see if I can get one. With the basted seam method you baste the seam and press it open. On the wrong side of the garment you centre the zipper teeth (zipper closed) over the seamline and pin it in place. Stitch the zipper onto each seam allowance and when it’s securely in place, remove the basting stitches. I’m sure there are many more “tips” and specifics than I’ve got here, but that’s the general jist of it as I recall.

On , Heather said: | sewingonpins.blogspot.com

Thank you for the great tutorial! There were a couple tricks in here that I’d never done before. I think I have a couple invisible zippers around – time to practice! :)

On , Steph said: | 3hourspast.blogspot.com

If you have the right foot for the job, you should never NEVER need to press open a zipper tape. They aren’t designed to be pressed, in fact they are specifically designed to roll. Don’t do your zips this way, you’re setting yourself up for failure.

On , Caroline said: | l-p.cc

Is it possible to disagree and agree at the same time? I press them when I don’t have the correct foot so I can see what I’m doing. I don’t see a difference in the end result. I get a nice flat-lying super-hidden zipper. Please elaborate.

And thanks for the tip on the plastic foot. I assume you’ve tried them?

On , Sarai said: | colettepatterns.com

Steph, I respectfully disagree with your experience. I always press my coils, even with my fancy Bernina foot, and get better results that way.

Yes, they are designed to roll, and will continue to do so once you zip them up again. I believe even the Coats and Clark Sewing book (manufacturers of invisible zippers) says to press them lightly (see this reference on Sewing.org). I also have some manufacturer instructions right here that say to press lightly “for easier application.”

Anyway, I know some people prefer not to press them and I respect that, but your comment seems a bit extreme. I’ve yet to have a “failure” because of pressing per manufacturer’s instructions.

On , Caroline said: | l-p.cc

I also thought the word NEVER was extreme, since everything I’ve read says to press them. Though if you have a good zipper foot (and some I’ve used have crummy grooves) it kind of takes the need to press the zipper out of the equation, which is sometimes nice.

On , Steph said: | 3hourspast.blogspot.com

Also, make sure it’s the metal foot designed for your machine. The plastic snap on feet are basically worthless.

On , Leah said: | strugglesewsastraightseam.wordpress.com

Is there a way to do this by hand? I know it’s weird but I prefer doing zippers by hand, I feel like I have more control.

On , Susan – Knitters Delight said: | knitters-delight.blogspot.com

I really appreciate this tutorial. I have a Bernina including the correct feet, but still have had a hit or miss result on my construction. Low and behold, I realize now that I have been sewing the zipper right side up with the fabric wrong side up. I am happy to now do the reverse.

One question that another commenter also asked – isn’t the bottom portion of the seam suppose to be sewed first to avoid bubbles below the zipper? I vaguely remember hearing that somewhere.

On , Sarai said: | colettepatterns.com

Hi Susan… is it possible you are thinking of a standard (non-invisible) zipper? If you were doing a standard centered zipper, you would sew the seam at the bottom first. With invisibles, you leave it open. If you look at the photos for steps 6 and 7 above, you can probably see that it would be much harder to sew the zipper at the bottom in if the seam was stitched.

On , Lola said:

Great tutorial! However, I would like to make a wish for a following one – how to finish an invisible zipper with the facing or lining… I just never get really clean results there!

On , Caitlin said:

Patricia’s comment is great! I also found a tutorial and posted about it in the invisible zipper thread in our forum.

On , Patricia Austin said:

Veronica Shaeffer from http://www.vsgowns.com/ just gave me this extremely helpful tip when dealing with lining AND invisible zippers. I had just posted this very question only moments ago. Kismet! Thanks Veronica!

“Btw, you can machine stitch the lining to an invisible zipper by turning the dress inside out and then laying the lining over it. Match the lining edge to the zipper/fabric edge and then stitch with your invisible presser foot. The zipper will be between the self fabric and lining, if that makes sense. Actually very easy once you give it a try!”

On , Steph said: | 3hourspast.blogspot.com

I appreciate the respectful disagreement, which is why I never say much when I see similar tutorials. I assume I’d be tarred and feathered for disagreeing. Please know that I teach sewing, I have taught hundreds of women (not many men come to classes) to sew invisible zippers, and I can boast a 100% success rate. I take great personal pride in the success of my students.

I see a big problem with plastic feet. They don’t function as they ought to. I have never seen one perform the function they should. Metal invisible zipper feet usually range in the $18-42 price range here in Australia depending on the model, and the plastic foot retails for $3. The metal foot may need to be specially ordered even though the shop where I works carries plastic feet. If someone wants to try the plastic foot first for whatever reason, I warn them and then do my very best to teach them to put in a good invisible zip.

I define “good” as they shouldn’t have to break their brains and offer their firstborn to the sewing gods in order to get a good result. Good results with plastic feet in my experience=nil. Never. I can stand by that. Further, I find if I let someone buy a plastic foot and try to put in a zip that several things may happen:

–Melting the zipper as they press it. Unless I press it myself, there’s a high likelihood of someone over-pressing and the zipper teeth stick together. In such a case, I humbly suggest it may be a faulty zipper and give them a new one.

–Bad zipper. A plastic foot simply does not (as far as I’ve seen it) roll the zipper coil effectively, and generally leads to sewing too far from the zipper coils or the sewist mistakenly sews over the coils. Either way is not a good invisible zip.

I’m not saying that with a great deal of patience and perserverance a beginner or intermediate sewist can achieve a good invisible zip. I just say that these kinds of tutorials actually make my blood boil because I know it doesn’t have to be that difficult or mysterious. A good invisible zipper foot engineered specifically for the machine and the task will present perfect results every time.

Sometimes I offer the alternative of the right metal foot to someone who insisted on using a plastic foot. Some people need to make mistakes before they will listen. That’s fine. I’ll get the right metal foot, let them try it, and they immediately buy it, even at $42. With the right technique and the right foot, an invisible zipper takes about the same amount of thought as fusing interfacing properly. I don’t think we as sewists should celebrate making life harder on beginners and intermediates. I know that’s not what you’re saying here and I appreciate that you regularly post new and interesting tips and techniques, but this tutorial leaves me cold.

On , Caitlin said:

Hi Steph,
Thank you very much for offering your view on the tutorial. I can understand your frustration with seeing advice contrary to your own, especially when you feel that it is impeding learners. While you disagree with the pressing of the zipper and the plastic foot, I wasn’t sure what upset you about the tutorial. I have created a post in the forum about invisible zippers and welcome your input.

While we try hard to help all sewers learn the best ways to do things, we do make mistakes. In this case, I think that it is a difference of opinion. Sarai and I both see sewing as something that suits each person differently. In this case, you have had no positive experience with ironing zippers or plastic feet. However, Sarai and as others have had success. I think that this is a good example of how two methods work differently for others.

I would like to stress that beginners will make mistakes and we would love to help them avoid them! If we felt that our advice was a hinderance, we wouldn’t offer it. As with all tutorials and methods, each sewist should test it out to see what works best for themselves.

Thanks again for your input and please feel free to continue the discussion in the forum.

-Caitlin

On , Kelli said:

Steph

I read your comment with great interest. I am currently trying a new technique that I have heard about – to insert invisible zippers ‘in reverse’. I have explored the web for directions to no avail.

I see you are a sewing teacher so you maybe can help me.

On , Steph said: | 3hourspast.blogspot.com

I’ll add, respectfully, I have never seen instructions to iron the coils included on a zipper, but I know I haven’t seen every brand of zipper out there.

On , Amanda said:

Thank you! I love this tutorial. It’s really easy to follow.

I have inserted an invisible zip in the past with some success (and a few mistakes!) but now I see where I have gone wrong.

So well timed too – I’m nearly ready to put the zip into my parfait dress.

On , Faye Lewis said: | fayessewingadventure.blogspot.com

THANK YOU, THANK YOU, THANK YOU. My problem was knowing just how far to place the zipper tape away from the edge of the fabric. This clear tells and shows me. Thank you again!

On , Layla said:

While a good specialized foot may save time, and help you achieve great results without the learning curve, I’d like to mention that I have used my regular zipper foot to install invisible zips using the same instructions illustrated so clearly in this well-photographed tutorial. I’ve never melted a zipper, and ironing (mentioned on sewing.org which my zipper manufacturer coats and clark references on their invisible zip blog post) is a crucial step for me, using the regular zipper foot.

I appreciate Steph’s frustration and the fact that her long experience with her method is highly successful. But I also agree that this is a case where this common method works for many people, is not technically inferior (as long as you watch the temp of your iron, probably the best take home point of this particular sidebar), and for people like me means you don’t spend the money on another foot and can instead buy more zippers and fabric ;)

I continue to appreciate these clear tips from Colette Patterms – and I also enjoy the discussions they inspire.

On , Heather said:

So, what if someone was just now at the point of inserting an invisible zipper, and, never having done one before and having seen nothing in the pattern or pattern instructions indicating that a 5/8 seam allowance was required, is now left with a 1/4 seam allowance to work with? Is there anything wrong with using a smaller seam allowance?

Thanks for the great, and very timely, tutorial.

On , Christine said:

You’ve probably already figured out by now that you *can* use a smaller seam allowance, though it can make lining up the edges of the zipper tape and fabric more difficult (since you can’t see through the zipper tape to the fabric below). If it’s all you have to work with, then that’s what you’ve got to use. I would suggest finishing the seam allowance with a triple zigzag stitch to minimize any fraying which might cause the zipper application to fail further down the road, and marking the seamline so you have a guide to line up the zipper coil against.

My preferred method for any type of zipper application, though, is to cut my seam allowances to match my zipper tape width (measured from outer edge to center of the coil). For example, if I am doing a centered or invisible zipper application, I cut my fabric out so there is a 1/2″ SA the length of the zipper insertion (because my zipper tape width is slightly less than 1/2″, and the rest is taken up with the turn of cloth). If I am using a commercial pattern, this usually means trimming 1/8″ away from the SA. I find that it’s so much easier to sew edges that match each other (an added bonus – I don’t need to use pins!).

I learned this from the Fashion-Incubator.com website (which Caitlin referenced above). The methods described on that website are the *only* ones I use to apply zippers anymore.

Inserting an Invisible Zipper

[...] Colette Patterns – Installing an Invisible Zipper [...]

Muslin is Actually Calico « VickikateMakes

[...] by me, it’s an  invisible one and it ain’t bad if I do say so myself!  I followed this tutorial from Colette as it was straight forward and I got it, Sunni’s method didn’t suit me, [...]

Secrets of the Invisible Zipper

[...] I prefer to put the zipper in before the seam is stitched, I do love Caitlin’s tutorial as well.  I think her little helpful hints in the pink boxes is just the cat’s pajamas!  [...]

Colette Patterns’ Sewing Tutorials : Craft Stew

[...] Craft Link : Colette Patterns’ Sewing Tutorials [...]

On , Kelli said: | smalltownstitcher.blogspot.com

Just wanted to say thanks for the great tutorial. I haven’t put in an invisible zipper since I was about 10 learning how to sew in 4-H and that was with help from my sewing leader, so I really couldn’t remember how to do it. I followed your tutorial exactly except that I don’t have an invisible zipper foot. I’ve got a Viking and didn’t think to use my buttonhole foot, I used my blind hem foot. It’s got the perfect ridge for the coil to sit in. I am bookmarking this for future reference. Y’all are great, keep it up!

On , Lizzy said:

I’m doing a decent job with the invisible zippers now but cannot for the life of me make a clean finish at the top with a hook and eye. Any tips for that?

On , Christina Draper said:

You need to make sure the hook and eye are set with the top of the hook and the top of the eye even to the edge (fold) of your fabric. The edges of your fabric will meet and there should not be a gap between them. If this isn’t your problem, then your zipper may not be stitched on properly. A lot of people make the mistake of leaving the zipper zipped up when they stitch it on. You should have the zipper unzipped when you are stitching the top part on. If it is left zipped up, the zip part of the zipper will get in the way of your sewing and create a little wave in your stitch line. Sometimes this will force the two top ends of the zipper out, rather than in.

On , Amber said: | amber-elayne.blogspot.com

Thank you so much! I’ve never actually seen this so easily done!

On , Claudia said: | customwearsbyclaudia.com

Thank you for another great tutorial! I recommend this blog to all of my sewing students and look forward to each new post. I guess I am with the few who do not use the plastic zipper foot. I roll the teeth of the zipper as ‘open’ as possible, press and use my sewing machine’s regular zipper foot. I always have great results and have never damaged a zipper with the iron.

On , Duckie said:

Huzzah! Just used this tutorial to put the (non-invisible) zipper into my nearly-finished Ginger skirt and after 5 years of sewing, it’s the neatest gosh-darned zipper I’ve ever inserted. Glorious.

Pretty Little Plaid Skirt Tutorial | Sweet Little Chickadee

[...] Sew up one side of the skirt, then tackle the zipper. Colette Patterns has a good invisible zipper tutorial here. [...]

DIY: Sewing Up A Sea of Turquoise « Sheila Zeller Interiors

[...] on how to install an invisible zipper… 3 different sets of instructions! In the end I used this tutorial by Colette Patterns along with a few extra tips from my trusty old Reader’s Digest Guide to [...]

On , Lisa said: | GracieLouDesigns.Etsy.com

Thank you, THANK YOU! In my 15 plus years of sewing, I’ve lost track of the number of times I’ve been aggravated from installing invisible zippers, and I’ve never been happy with the results….until I read your instructions! There are so many helpful tips that I had just never come across in any other instructions before. I just finished installing the zipper on my Ginger skirt, and I am pleased and satisfied beyond words! You are never too old to learn a better way of doing something!

On , Lyne said:

Yay ! my first ever invisible zip ! thanks now feel confident to finish my parfait

Cartoon-esque Rooibos | | Scruffy Badger TimeScruffy Badger Time

[...] been.Now, invisible zip sewing is a new one for me, & I also followed Colette Patterns online tutorial.  It was very clear, but didn’t stop me messing it up first time.  Never mind.  I am [...]

FO: Simplicity 2452 « The No-Method Method to Happy, Healthy Children

[...] I used this tutorial to insert the zipper, although this one at Colette also looks good. I’m pretty happy with it. There’s a slight bulge at the bottom left, [...]

On , Gayle said:

This is a great tutorial. It’s wonderful that all of these things are available online, and I must say that the Coletterie, as it’s now named, is the first spot I check for tutorials, as the pictures and writing are crystal clear.
I teach private and semi-private sewing classes, and was looking for an invisible zipper tute to send to a friend in another country, as I’m lazy and knew I could find it online rather than have to take pictures myself! I bring up the classes, as I teach basic zipper installation in the first two hour class. Once you can sew a straight line, you can install a zipper, so far as I’m concerned, and I think that so many of (myself included!) scare ourselves with the perceived difficulty of sewing tasks, psyching ourselves out. I spent years of my sewing doing anything and everything to avoid installing zippers, and could have kicked myself once I finally “manned up” and did it, as it was so easy, not the monster I’d considered it to be.
Which I guess is a long and round about way of thanking you for demystifying sewing for so many people.

Invisible Zipper Foot to the Rescue « Sew Well

[...] with this magical foot.  I do have to give due credit to both Sunni’s tutorial and the Colette Pattern’s tutorial for why everything finally went so [...]

On , PDX Gretchen said:

Thanks to your wonderful tutorial, I’ve just installed the nicest invisible zipper I’ve ever done. On a Ginger, to boot. Thank you for such clear instruction, in your tutorials and your patterns.

Ginger Skirt in Candy Trees « Night Knitter

[...]  I also like the thorough tutorials on the Colette blog.  I used the tutorial on how to insert an invisible zipper to make the Ginger skirt (Colette 1016).  I’ve sewn in my fair share of zippers, but I need [...]

On , Christina Draper said:

I’ve always just used regular zipper feet to install invisible zippers. Really, the most important part of it all is pinning everything EXACTLY. Then get as close as possible to the teeth of the zipper.

On , Faye Lewis said: | fayessewingadventure.blogspot.com

Thank you very much for this tutorial. My application is still not as easy as eating cake, but I’ll keep practicing and maybe one day it will be.

On , Marie said: | asewingodyssey.blogspot.com

Just wanted to say that I used to hate and mess up zips every time I attempted them, until I found this brilliant tutorial…many thanks!

On , donna said:

thank you for this great tutorial. i made a soft wool ginger skirt and the zipper looks professional! i have never had a zipper to come out so perfectly. i don’t have an invisible foot so I used my clear plastic foot that i use when making small tucks/cording. it worked fine.

On , Faye Lewis said: | fayessewingadventure.blogspot.com

I really need to thank you each and every time I insert an invisible zipper. Just did another one – THANKS!

On , Mary said:

Have yet to try your advice, which is more thorough than what I had been given elsewhere. However, nowhere do you (or my other source) state whether one is starting to install the zipper on the left or right half of the garment. Considering you start with the zipper upside down and then flip it over, there is an inherent possibility of confusion, and some of us manage to sew despite of a severe lack of spatial relations

Colocando um ziper invísivel « Falando com os meus botoes

[...] Achei esse post num tutorial de blog, e colocar zipers é sempre chato, e complicado para quem não tem experiencia. Se for invisível é ainda mais chato o endereço é este aqui: http://www.coletterie.com/tutorials-tips-tricks/tutorial-installing-an-invisible-zipper [...]

almost finished dress! « Look, I made A Dress!

[...] I finally have a decent dress!  I followed grosgrain tutorial here to make the dress and used  this awesome zipper [...]

Pretty Quirky Pants | 50's Skirt Adventure #1 - DIY Pleated Skirt

[...] essential. The series of photos below demonstrate how I attached it and the following links show a pictorial tutorial on how it is done and a very informative video explaining the different types of zipper foots along [...]

On , Jo said:

I have just made a skirt tonight and followed this tutorial to install the zip. It worked! The only thing was that I could have got closer to the teeth so the zip was more hidden, but I am absolutely stoked with my first go!!

Colette Sewing Handbook: Meringue Skirt | Right Side Wrong Side

[...] You have to switch to a regular zipper foot to complete the invisible zipper.  I found the Coletterie invisible zipper tutorial to be helpful.  The instructions in the Sew Everything Workshop were also good, as was this [...]

Giant Floor Cushions | Terrabyte Farm

[...] cleanable, so I gave each cushion an invisible zipper.  They are pretty easy to install, here is a great tutorial.  On the first two pillows (pink and orange) I used zippers I had on hand, I think they were about [...]

it’s invisible « A Thousand Dreams

[...] zipper foot,I found some information online assuring me I didn’t need one. I followed this tutorial,at the same place the pattern I was using is from.Ok,on to the pattern. I made a size 14. WHAT WAS [...]

Skirt Sew Along Part 3: Zippers « Sew Vac Outlet (Humble Sewing Center) Blog

[...] them, but I have done several and can still sometimes mix myself up. I often refer to this tutorial from Colette Patterns which is just pictures and [...]

On , Pat said:

OMG, you have the BEST tutorial for invisible zippers!!! Thanks!!!

Seven Essential Sewing Skills, from Sew, Mama, Sew! | sewlucky

[...] for this is How to Sew a Zipper Pocket from Makebabystuff.com Guide to ZippersInstalling a ZipperInstalling an Invisible ZipperInserting an Invisible ZipSewing a Vintage-Style Lapped ZipInserting a Hand-Picked [...]

Butterick 6582, I’m in love | Dapper Duds

[...] seam binding (from 1966, naturally). I inserted an invisible zipper  for the first time (thank you Colette Patterns) and hemmed by hand using a catch stitch (thank you [...]

Should you give up on a sewing project? « lizzylikescake

[...] weekend I finally got started again. I put in a passable zip (thanks to this Colette tutorial). Technically the zip isn’t quite as ‘invisible’ as I might have [...]

On , Kate Setzer Kamphausen said: | modiste1000.com

This tutorial is great! Just a further bit of information: I buy and give away multiple copies of THE READER’S DIGEST COMPLETE GUIDE TO SEWING. Any edition. Check Ebay. Seriously, it tells you almost everything from “this is a needle” (with useful information about the sizes of needle eyes!) to “here’s how to make a welt pocket” and everything in between, INCLUDING how to install all kinds of zippers. Fantastic stuff.

On , Lysandra said: | geekchicfashion.etsy.com

Thank you. Thank you. Thank you. For this amazing invisible zipper tutorial. I have never sewn a zipper, let alone an invisible one, but I used your tutorial and installed a beautiful invisible zipper in my chiffon maxi skirt. It’s not perfect, but pretty darn good for my first go! Your tutorial was a life saver!

On , Marge Freeman said:

I have sewn many invisible zippers into pillows without cord, I have a request to sew them into pillows with cord, is that possible?

Nicole Williams (nicolewilliams) | Pearltrees

[...] Tutorial: Installing an Invisible Zipper | Coletterie Items Needed: [...]

Yamileth Teresa (yamilethteresa) | Pearltrees

[...] Items Needed: invisible zipper Tutorial: Installing an Invisible Zipper | Coletterie [...]

On , Janett said:

I’m almost embarrassed to ask, but could you define “end of zipper” please? Is it the point where the foot can’t go any further, or the very bottom of the zipper tape?

On , Joyce Rogan said:

Thanks for the clear and helpful video. But I am trying to put a zipper into a seam in a pillow that has welting around the four sides. How do you do that?
Joyce

On , Allison said:

great tutorial!

On , Jean said:

I have used invisible zippers for years I am 64 years old and am now teaching my granddaughter how to put in invisible and regular zippers. I have used many different sewing machines over the years and always used the plastic invisible zipper foot. I find it quite useful. I have never had any trouble with it. This summer we are going to spend a week or two putting nothing but zippers in scrap material both types of zippers, I concider myself quite capable of teaching her and others as I have been sewing since I was 11yrs old
I was taught by my grandmother. This tutorial is very well presented, it is well understood, and newbees will not have any trouble understanding it. Congratulations Job well done

On , Rachel said:

Thank you so very much for this tutorial. I have installed my very first invisible zipper — with the controversial plastic feet — with very good results. The zipper is even installed on the side-seam of a dress! Great tutorial….

On , Renee said:

Thanks so much for this tutorial! I actually dived straight in and decided to use an invisible zipper on my first ever sewing project and it has turned out perfect! Your instructions are very easy to understand even for a complete novice, I’ll be checking out all your other tutorials now… Thanks heaps ;-)

On , Angelicladydee said:

I have struggled with invisible zippers for some time now. Your instructions have really made a difference. What used to be a very difficult task is now an easy one. Your instructions are very easy to follow and produce desired results. Thanks for your unselfish publications of these instructions.

Angelicladydee
Southaven, Ms.

On , Erica said:

What drives me crazy about these tutorials, and the instructions in the book, is that the sample fabric you use doesn’t have an obvious right and wrong side. This means it’s harder for me to visualize what’s going on. Just an idea for future posts :)

Hazel Muslin Continued | Lucky Lucille Handmade

[...] easier than standard centered zippers. They require way fewer steps! Colette has a pretty great tutorial for installing invisible zippers, but here’s my take on it [...]

On , Affordable said: | affordablefashioncenter.com

Nice tutorial. Thanks.

On , Nancy said:

Thank you very much for this tutorial. It was terrific in every way. I have the Bernina invisible foot and it worked very nicely. This is the first time that I have tried to install an invisible zipper (I have tried to read about it and watch some videos on line) but your tutorial was the greatest. As soon as I tried it – everything worked beautifully. First time on my muslin test ginger!!!!!!

Thank you ever so much and keep these easy to follow instructions coming. I shall use this method often – if not always.

PS love your patterns

Colette Macaron – 2012 Wedding No. 1 « Konnie Kapow!

[...] but I quite like the presenter.  Wonder where she got those nails done?!  This tutorial from Colette is also very [...]

On , Cheryl said:

Thank you so very much sharing with me on how to put in my very first zipper. I found your tutorial to be very helpful. Again Thank You!

On , Debbie said:

I also found the tutorial very helpful especially in completing the seams, I have run into trouble with puckering.
My bigger problem is after installation the zipper doesn’t run up and down smoothly and at least half the time the zipper splits and is not usable anymore
I’m wondering if how I press it is causing a problem or maybe the plastic zipper foot.

FO: Crescent Skirt « a girl in winter

[...] next time, though. I serged them for a 3/8” seam before inserting an invisible zip, following the instructions from Colette. However, the 3/8” seam made it fiddly to sew up the back seam by the end of the zip. Next time, [...]

2-in-1 Sewalong: Finishing

[...] Inserting the Zipper Let’s start with the zipper insertion. I did an invisible zip on both dresses. At one point or another I was not terribly fond of invisible zippers, but I’ve come around. In fact, I do love a good invisible zipper and these days they are easier for me to insert than a traditional zipper. I’ve got a tutorial here and my one emphasis on invisible zippers is that you should stabilize the zipper opening before insertion. Those zippers are such flimsy little things and really silk organza or fusible tricot (my favorite, btw) work really great to give these zippers a little oomph and strength. For added fun, here’s a few more of my favorite invisible zipper tutorials: Tricks of the Trade: Inserting an Invisible Zip Tutorial: Installing an Invisible Zip [...]

Hazelicious « Cuckoo Chanel

[...] crying over the muslin at this stage. I also bothered to go to the Colette website to the great invisible zipper tutorial , and bothered to figure out how the invisible zipper foot I bought actually attaches to my sewing [...]

I got distracted – Sewaholic Cambie Dress « Kim-ing

[...] the pattern was! This is probably the best technically executed dress I have made. With the help of Coletterie I even made my first invisible zipper, although I quickly ditched my invisible zipper foot for my [...]

On , jenny said: | byrdiecouture.blogspot.com

I’ve been sewing invisible zipper for years but I still learned something new from your tutorial! Thank you for showing how to finish the seam below the zipper. I’ve always tried unsuccessfully to meet the zipper seam to the rest of the seam and ending up fussing and spending way to much time trying to make It perfect. I used your tip on overlapping the two seams a bit apart and It worked perfectly!

On , angie said:

Thanks so much for the tutorial. I am returning to sewing after a 10 year hiatus and can’t recall if I’ve ever encountered invisible. The instructions on my pattern are incomprehensible so I’ve looked at several IZ tutorials on the web and this is by far the best. Bookmarking your site and will check out your other content for ideas and patterns as soon as I finish my current projects. Again, THANK YOU.

On , linda said:

I’ve been trying to get the whole zipper thing down for years and you’vve explained it perfectly.

Thank you

An Ikat Macaron « the creative counselor

[...] include instructions to install an invisible zipper in their pattern booklets, but there is a great tutorial on their blog. (And a video tutorial [...]

On , Helen said:

first time i have inserted an invisible zipper, with your guidance it was easy and it looks good. thank you

On , beth said: | readyruthieoriginals.com

I don’t have the fancy invisible foot but I’ve done fine sewing invisible zippers with a regular zipper foot. I find it helps to baste the stitch, then press it flat. It makes it easier to see where the coils need to line up. I pin them as described, and sew with the regular zipper foot.

On , Bernie said:

But how do you put an invisible zip into a lined dress?

On , Dorcas Prentice said:

This is an excellent tutorial, a really great help to me. I am a veteran sewer having been sewing for over 50 years but haven’t had much need for installing zippers, much less invisible ones with my recent sewing projects. It was so great to find this so quickly when I googled for help with this issue. The pictures couldn’t have been better and the written instructions were concise and easy to follow. I was sewing a bridesmaid dress for my youngest daughter, the dress and zipper turned out great thanks to your help!!!

On , Bernie said:

That’s great but it’s still not a lined dress!

On , Sarai said: | colettepatterns.com

My book has some info on how to attach a lining to the zipper by machine. It’s actually pretty easy.

On , April said:

I just found this tutorial, obviously many months after the original post. I followed it to the letter and had perfect results the first time out installing an invisible zipper into a flocked taffeta skirt for my daughter. Also, for Caroline, in the months since she posted that there was no invisible zipper foot for owners of Viking machines, one has been introduced, part #413286545. Mine cost around $30.

Thanks again for sharing.

On , Sonia White said: | soniasscrapbooking.blogspot.com.au

I have just done my second zip with your tutorial. I am so excited and thrilled with the result. Your tutorial was very easy to understand and follow. Thank you so so much!! I will NEVER go back to my awful attempts at an ordinary zip.

On , ABCameo said:

I have a question. There’s a home decorating fabric store nearby which is where I mostly buy my fabric. The material they carry is so beautiful and unique. I’m only interested in garments sewing and especially prefer creating one-of-a-kind boutique-type looks.

I made a top with an invisible back zipper out of a somewhat stiff home decorating fabric. Though I pressed several times, the fabric sorts of pops up slightly standing away from the seams where I attached the zipper. The zipper is in correctly, and the fabric looks really good since I also made pants in the same material, but it bothers me that the fabric doesn’t sit 100% flat when zipped.

Is there a way to make sure fabric sits nice and flat along the folds once the zipper is in place? Should I slip some fusible tape alongside the zipper and seam to keep the fabric down close to the zipper tape? Truthfully, I know I’m going to continue using home decorating fabric for my creations so I’m pretty sure this issue with “pop up” again. Many thanks for any advice.

Winter White | Crystal Pleats

[...]  My first invisible zipper!!  Hip hip hooray!  With the help of both of these Colette tutorials: Photo tutorial and Video tutorial.  I found the combination of both helped my success on the first [...]

On , Kittee-Bee Berns said: | kitteekake.blogspot.com

Thanks for this, Sarai! Until today, I’ve been installing invisible zippers with a regular ol’ zipper foot, but I went over to the Montavilla Sewing Center (attached to Fabric Depot) and they were able to find an invisible zipper foot that works on my old Singer. So happy!

One question: On the Rooibos dress, you are supposed to sew about 1.5 inches of the side seam first, before installing the invisible zipper. Do you have any advise on sewing seams like this, that aren’t open at the top?

xo
kittee

On , Sarai said: | colettepatterns.com

It’s basically the same process. You just want to make sure your zipper stop is aligned with the top of the opening, so there’s no gap. I like to stitch the tape at the top to the seam allowance as well, to keep the top of the zipper from flipping outward.

But installing it is really just the same!

Nap Mat | Sewing Novice

[...] an invisible zipper, but for the foam section I used a regular zipper.  Here is a tutorial on how to install an invisible zipper (I will actually have an invisible zipper pillowcase tutorial soon) and here is the regular zipper [...]

Make a Dirndl skirt! |

[...] zip but you could put any zipper in. Ididn’t take any photos of this but here is a good tutorial. Once the zip was in I finished the last [...]

Nitty Gritty Dress Details - C Sews

[...] sections, carefully keeping the lining of the bodice out of the way. I found the  tutorial “Installing an Invisible Zipper” on Coletterie to be very [...]

On , Robin said:

Do I apply the neck facings before or after applying the zipper?
There is no mention of this in your instructions. I already put my
neck facings in. Now what?

On , Janice Linden said:

This is a great tutorial. I have put in many invisible zippers when I sewed construction in the 70′s and some in the 80′s but quit to work and raise my daughter and husband. I am now in my 60′s and went brain dead when my two grand nieces asked me to fix their skirt zippers, one regular and one invisible. The regular went well but then I totally forgot how to insert the invisible one. Thanks for having such a clear tutorial with great pictures. It keeps us oldies sewing.
Janice

The Search for Sewing Advice After Hours - C Sews

[...] Colette Patterns Tutorials – Sarai Mittnick, Colette Patterns founder and designer, author of The Colette Sewing Handbook, covers a variety of topics, ranging from working with fabric to fitting and adjustments. She has a nice explanation on installing invisible zippers. [...]

On , Christine said:

This is very helpful, the little things make a difference, like ironing the zipper.
I have been having trouble with step 11 & 12, probably bc I am a beginner sewist. So what I have been doing recently is sew everything by machine except step 11&12. I mark the line, and hand sew for more precision so the zipper matches the seam, and I hand sew it 2x, so the stitches are strong.

Is that weird? Has anyone encountered problems with that? Someday, I will master being able to match the zipper and lines on the machine.

We’re sorry, comments for this post have been closed.